modulstand frames are built on the 62mm profile standard — 62mm profile width, 31mm hole diameter, 62mm center-to-center hole spacing, and frame sizes in exact multiples of 62mm. Our connectors are fully interchangeable with existing 62mm system hardware. Verify compatibility with your own inventory before you buy.
Every frame, connector, and reinforcement in the 62mm ecosystem is built around three precisely controlled measurements.
Every connection point on a 62mm profile frame uses a precisely machined 31mm diameter hole. This universal dimension ensures that connectors seat correctly across any manufacturer following the same specification.
The distance between the center of any two adjacent holes is exactly 62mm. This is the grid that gives the system its name — and it’s what makes every frame, every connector, and every accessory interchangeable.
All frame dimensions are exact multiples of 62mm. A 496mm side is 62×8. A 992mm side is 62×16. A 2480mm side is 62×40. This mathematical precision is what allows frames from different manufacturers to align perfectly.
How modulstand frames compare to the established 62mm profile standard. Every critical dimension matches.
| Specification | 62mm Grid Standard | modulstand |
|---|---|---|
| Profile cross-section | 62mm square | 62mm square |
| Hole diameter | 31mm | 31mm |
| Hole center-to-center | 62mm | 62mm |
| Frame size rule | 62mm × N | 62mm × N |
| Frame construction | Profiles welded to size | Profiles welded to size |
| Frame-to-frame connector | M26 bolt through 31mm holes | M26 bolt through 31mm holes |
| Frame-to-base connector | M8 fastener | M8 fastener |
| Material | 6063 aluminum | 6063-T6 aluminum |
| Surface treatment | Bare (no anodizing) | Anodized finish |
| SEG fabric channel | Compatible | Compatible |
| Standard frame example | 992 × 2480mm | 992 × 2480mm |
| Tool-free assembly | Yes | Yes |
Material advantage: modulstand uses 6063-T6 aluminum with full anodized surface treatment. T6 heat treatment provides higher yield strength and hardness than T5. The anodized layer creates a smooth, corrosion-resistant surface that looks more professional and lasts longer than bare aluminum.
Our connectors and reinforcements are fully interchangeable with existing 62mm system hardware. Test it yourself with our free sample kit.
The primary structural connection. The M26 bolt passes through the 31mm holes to lock two frames together with precision alignment. This is the most frequently used component in any 62mm system build.
Installed at the top or bottom of frame joints for structural rigidity. All reinforcements use M8 fasteners.
| SKU | Type | Use |
|---|---|---|
| 23 01 0101 | 180° straight | Two parallel frames |
| 23 01 0102 | 90° corner | Two perpendicular frames |
| 23 01 0103 | 3-way | 180° + 90° junction |
| 23 01 0104 | 4-way | Four-direction junction |
| 23 01 0105 | 90° alt | Alternative 90° corner |
M8 fastener secures frames to weighted baseplates for freestanding structures. Compatible with standard 62mm system baseplates.
Watch our frames connect with existing 62mm system inventory. No modifications, no adapters — just bolt together and build.
This video demonstrates: M26 connector insertion, frame alignment check, SEG fabric installation across mixed frames, reinforcement installation, and stability test.
We don’t ask you to take our word for it. Order a free sample kit and run these tests with your own inventory.
Use the M26 connector to bolt a modulstand frame directly to one of your existing 62mm frames. The bolt should pass through both 31mm holes smoothly and tighten with no play.
With two frames connected, verify that the surfaces are perfectly flush. Run your finger across the joint — there should be no step, no offset, no gap between frames.
Install a piece of SEG fabric across the joint between a modulstand frame and your existing frame. The silicon edge should seat continuously through the channel with no interruption at the transition point.
Use one modulstand frame and one existing frame to build a 90° corner. Install a reinforcement bracket. Push gently from multiple angles to confirm structural stability. The connection should feel identical to your existing setup.
Our 6-page technical report includes detailed dimension comparisons, material analysis, test photographs, and compatibility verification methodology. It’s the document your engineering team needs to approve the purchase.
✓ Dimensional comparison (all critical measurements)
✓ Material & surface treatment analysis
✓ Connector compatibility verification
✓ SEG channel cross-section comparison
✓ Independent test photographs
We respect your privacy. Your information is used only to send the compatibility report and relevant product updates. Unsubscribe anytime.
Order your free sample kit and test with your own inventory. You only pay shipping.
