M26 frame connectors, reinforcement brackets, M8 fasteners, and baseplate hardware designed around the 62mm connection grid and 31mm frame holes — helping builders expand existing 62mm system inventories after physical fit testing.
The modulstand hardware system is designed for 62mm modular frame planning. Builders with existing 62mm inventory can use sample testing to verify physical fit before production orders.
M26 bolt connectors designed for frames with 31mm connection holes. The primary structural connection in 62mm system builds.
Five bracket configurations designed to add rigidity at straight, corner, T-junction, and crossroads connections. Installed at frame tops and bottoms.
Baseplate connectors, M8 fasteners, and complementary hardware for freestanding and floor-supported structures.
The M26 connector is the backbone of the 62mm modular frame system. This large-format connector is designed for frames with 31mm connection holes, locking two frames together at the connection point. It is the most frequently purchased hardware component for exhibit builders working with 62mm system inventory.
The connection is designed to support clean frame alignment for SEG fabric and rigid panel applications when the frames and hardware are correctly specified and installed. Final alignment depends on frame condition, installation method, and project setup.
| SKU | 21 01 0101 |
| Connector type | M26 bolt |
| Designed for | 31mm diameter holes |
| Weight | 0.2 kg |
| Material | Steel, zinc-plated |
| Tool | Allen key or hand tighten |
Sample testing recommended: modulstand M26 connectors are designed for 62mm system frames using 31mm connection holes. For existing third-party inventory, modulstand recommends sample-kit testing before bulk orders to verify physical fit.
Reinforcement brackets install at the top or bottom of frame connections to add structural rigidity. Each bracket type is designed for a specific junction geometry. All brackets use standard M8 fasteners (SKU: 21 02 0101). Final bracket selection should be confirmed based on project requirements.
Designed to add rigidity at inline connections where two frames meet end-to-end in a straight line (180° flat). Commonly used for linear backwall sections.
Designed to add rigidity at right-angle connections (90° perpendicular). Commonly used for corner layouts, L-shaped walls, and enclosed booth structures.
Designed for T-junction connections (180° straight + 90° branch). Used where an interior wall meets an exterior wall or where a dividing wall intersects a backwall.
Designed for crossroads intersections where walls meet from four directions. Used in complex grid-based booth layouts and multi-room structures.
Alternative 90° corner configuration with a different mounting geometry. Final selection between standard and alternative 90° brackets depends on project layout and installation approach.
All reinforcement brackets are secured with M8 fasteners (SKU: 21 02 0101, weight 0.1 kg each). M8 fasteners are sold separately and can be ordered in bulk. SKU values should be verified during quotation before production orders.
Weighted baseplates support many freestanding exhibit layouts where floor-level stability is required. Frames connect to baseplates using M8 fasteners. For freestanding structures, baseplate quantity, ballast, and support requirements should be reviewed during quotation based on project conditions.
| SKU | 24 01 0101 |
| Connection | M8 fastener to frame base |
| Weight | 0.1 kg (connector only) |
| Function | Secures frame to weighted baseplate |
Beyond baseplates, modulstand offers complementary accessories including leveling feet, transport cases, and cable management components. Contact us for the complete accessories catalog and current availability.
The table below is a planning reference. Components are designed around the 62mm connection grid and should be verified by sample testing when used with existing third-party inventory. Final SKU availability, weight, packing, and ordering details are confirmed during quotation.
Volume quotation available: Hardware components can be quoted individually or in volume packs. Contact modulstand for current MOQ and quantity pricing, subject to availability.
modulstand M26 connectors are designed for 62mm system frames with 31mm connection holes. Because existing inventory may vary by manufacturer, age, tolerance, and condition, modulstand recommends physical sample-kit testing before bulk orders to verify fit for your specific equipment.
Connector quantities depend on frame size, structure type, load, and installation environment. Send your frame list or booth drawing to modulstand and we can recommend a connector quantity for quotation planning. Final hardware quantities should be confirmed for each project.
Some configurations may use M26 connectors alone, while others may benefit from additional reinforcement brackets. Reinforcement brackets may be recommended for taller structures, heavier display surfaces, freestanding walls, and project conditions that require additional stability. Your modulstand quotation will include bracket recommendations based on your project design.
Many standard hardware connections can be tightened with an Allen key (hex wrench). Required tools may vary depending on the structure, hardware selection, and installation conditions.
Yes. Hardware components can be quoted as standalone items, subject to current availability and order quantity. Many exhibit builders maintain their own connector and reinforcement inventory and reorder as their project volume grows.
SKU 23 01 0102 and SKU 23 01 0105 both are intended for 90° corner reinforcement. They differ in mounting geometry — the orientation of bolt holes relative to the bracket face. Final selection should be confirmed based on the project layout, hardware availability, and installation approach.
Baseplates are quoted separately because not all builds require them. Baseplate requirements depend on structure type, height, location, ballast needs, and installation conditions. Wall-mounted and suspended configurations may not need baseplates. Your modulstand quotation will include baseplate recommendations based on your project design.
Hardware may be quoted in small quantities or bulk packs depending on current stock, product type, and order requirements. Contact modulstand for current MOQ and quantity pricing.
Request a quotation for connectors, reinforcements, and baseplate hardware as standalone items or bundled with your frame order, subject to current availability.
